QR Nano Diesel Catalyst
QR Nano Diesel Catalyst
A new catalyst has been developed for the direct conversion of Syngas to diesel. While many small steps happen within the reactor and the catalyst, the totality of reactions results in a clean green synthetic diesel fuel suitable for transport vehicles.
To date, diesel reactors are huge, tall towers, very expensive and complicated to run. Very few operators exist that have the knowledge and experience to own and operate such refineries. Refining diesel fuel has been the domain of the multinationals and no smaller, independent companies could compete.
Now we offer a compact, economical, simple one step reactor refinery that is suitable for the average company to enter the fuel industry. Nano diesel is made from waste, domestic and industrial. Not fossil fuels. Nano diesel can be described as a renewable fuel, with little or no toxic emissions. The new reactors use the latest nano particle technology to simplify and miniaturize the process.
The architecture of the new reactor vessel uses 400,000 micro-tubes filed with catalyst to achieve this result. Much research has been done to arrive at a seemingly simple process.
The conversion process follows the general principals of the FT method discovered 100 years ago. The discovery of new parameters that govern the reactions allows us to build and offer these small reactors, able to be operated with minimal training. The reactors can be bolted onto any existing syngas generator and accept a variety of syngas qualities. Syngas varies a great deal depending on its source. This could be coal, gas, waste, green waste, tyres, plastics, medical waste, even toxic waste. The syngas will need to be standardised with processing before feeding into the new reactor.
The flow of syngas is delivered under pressure to the top of the tubes where the gas is forced through the nano-particle size catalyst and emerges at the bottom end as a liquid. In our case we achieve 80% conversion of all liquids to diesel. The remaining content is degasified and sent back for a second pass as conversion. Some waste gases are collected and used for other purposes. The quantity of original waste converts to diesel at about 5:1 ratio, meaning a 400 tons per day waste facility can make 80,000 litres of diesel per day. Syngas is generated at about a 1:1 ratio of waste to gas. Remember that gas expands many fold from an original dense waste material, so the ratio is a bit misleading.
The standard design parameters for a diesel reactor vessel is to operate at 250 degrees C, 20 bar of pressure, use cobalt/metal catalysts and to end up with a number of products from the same operation. These could be short and long chain hydrocarbons of C3-4 ranging up to C20 and above. The percentage yield of product varies on adjusting all known parameters.
All existing refineries use trial and error to arrive at a ‘sweet spot’ where the desired product is dominant. It is not an exact science, despite the claims of all the big companies. The exact chemistry of cobalt catalysts is not fully understood, but used anyway as it works. In our case, the reactor operates at 300 degrees C, hotter than most, but at a reduced pressure of only 10 bar, or 150psi. This is through the new design and the materials used. Pressure vessels are dangerous and explode when corroded over time. We have deliberately reduced the pressure to that of a coffee machine to ensure your safety and have a long working life.
Despite the higher temperature setting, (excess temperature generally leads to carbon deposition and blockage of the reactor) no excess coke deposits are formed, and no blockages occur. This is because of the complimentary chemistry between the two metals and the silica of the catalyst. The exact chemistry is a proprietary secret as is the carbon nano tube cooling sheets between every row of micro-tubes. The cooling is more effective than the normal water radiator type and can disperse the extra heat as needed. The silica catalysts work best at a slightly higher operating temperature.
All this is achieved because our catalyst allows a free flow of gas over itself and through the internal pores (holes) in the catalyst material. We avoid many of the traditional pitfalls of refinery catalysts through re-engineering naturally occurring Diatoms, or tiny organisms that have a pure silica skeleton.
QR has developed a catalyst that outperforms our competitors, from a natural source of silica and a method of embedding transitional metals to enhance the performance. The source of the silica is Diatomaceous earth (DE) that comes from a naturally acid environment, so the final product has excess reactive Bronsted and Lucas acid sites on the exterior surfaces of the catalyst particle. Carbocations are formed from hydrocarbons on these two acid sites along with the formation of carbonium ions by protonation of hydrocarbons as the initiation steps in the ionic chain reactions that lead to catalytic cracking.
In addition to Carbocations, reactive catalysts rely on their particle size, their pore size and the specifically the size and shape of the hole to allow the reaction of cracking molecules to take place. Cobalt is popular now as the metal component, due to its aversion to water produced as a side product, but very necessary for the reactions to take place. The water-gas shift reaction describes the reaction of carbon monoxide and water vapor to form carbon dioxide and hydrogen: CO + H₂O CO₂ + H₂ Cobalt will not absorb the water, nor loose its reactivity and so acts as a catalyst longer. It is not the only metal candidate but is the best one found so far for specifically converting gas molecules to diesel. QRNP’s are an alternative when combined on a silica carbide substrate, so this combination is as good, and less expensive to produce, and more forgiving in its properties as a transitional metal. We combine QRNP’s with the silica carbide lattice to give a high performing catalyst tuned to exact conversion parameters of diesel.
The following table lists the fuel products commonly produced from crude oil.
LPG Liquid Petroleum Gas C1-C4 50 degrees C
Naptha C5-C7 70 degrees C
Petrol C5-C10 120 degrees C
Paraffin/jet fuel……………….C10-C16 170 degrees C
Diesel C14-C20 270 degrees C
Wax C20-C50 400
Shipping bunker fuel C20-C70 600
Bitumen C70+ 700
There are a multitude of chemical names for these fractions and distillates. To simplify the paper, consider the C chain length and the temperatures needed to separate them. In an oil refinery cracking crude oil, this occurs in a tall distillation tower, processing large quantities.
Using Syngas as the feed, we only convert the diesel fraction of hydrocarbons directly from the gas and no other fraction. The catalyst pores are sized to only allow the C chains length of C14 - C18 to form. The resulting diesel still needs cooling, filtering, and blending to standardise the final product. Some small amounts of other fractions are formed as the system is not perfect. It is highly unlikely that 100% pure diesel will be ever formed using this type, or any type of reactor. In the future, new ways of assembling long chain hydrocarbons will emerge that allow such precision and the technology will probably be a combination of ultrasound, molecular sieves, and chemical templates. Given that diesel is the basic transport fuel of the world, this research will continue. The annual usage in Australia is 30 Billion litres, of which only 4% is domestic cars. The vast majority usage is industry, mining, truck and heavy machinery, shipping and electrical generators. Nano diesel competes directly with other products from Syngas production such as hydrogen, and electricity generation. Given the existing infrastructure in this country, diesel is poised to be even more dominant in the marketplace.
Diesel powers all stationary electrical generators, in public and private buildings, industry and domestic and accepted as the most reliable form of energy. Nano diesel is cheaper, renewable, and non-polluting, so will make all those generators more viable and useful. Price comparisons on diesel powered electrical generation shows diesel highly competitive against solar and wind. The technology for generators has improved with the use of ceramic materials, highly efficient engines, nano-particle coatings, and catalytic converters on exhaust.
The diesel reactor described here is a breakthrough in design and efficiency for conversion of syngas to fuel. Its compact size and simplicity of operation makes it suitable for regional councils and small business to enter the fuel market. Given the rising costs of all materials in industry and commerce, the reactor will be a stabilising influence on the fuel markets. The new catalyst is designed to be used in this reactor, although it can be utilised in other existing reactors with modification. The unique properties of this product are gained through the exact spacial distribution of transitional metals nano-particles in the lattice of the crystalline silica carbide. The influence of QRNP’s on the size and shape of the pores in the particle, creates a specific chamber for the conversion of syngas to diesel.
Components:
Silica carbide derived from Diatomaceous earth (DE) is the substrate material and an inexpensive source of quality silica. Pure amorphous silica is extracted from the DE, processed into carbide, and atomically doped with QRNP’s. The exact position in the atomic lattice is every 8th atom. The final silica powder nano particles are surface functionalised with QRNP’s coating lodged inside the terminal pores of the silica. The pore size is critical to the success of the reaction to ensure only saturated alkenes of C14-18 are produced. The Lewis acid sites inside the pores are maximised through the proximity of metal oxides on the surface and inside surfaces of the pore. By donating electron pairs they act as Lewis sites. Nano alloys melt at a lower temperature than bulk size, providing constant oxidation at the operating temperature of the reactor. The fine tuning of temperature and pressure are achieved through internal cooling of the reactor by dividing sheets of heat conducting material. The dispersion of heat evenly throughout the reactor allows the 3m long reactor tubes to maintain constant parameters.
The production is continuous rather than by batches, as the speed of conversion is tuned to the infrastructure. A 3 meter high reaction vessel with its associated equipment, can be mounted on a semi trailer and prime mover for a mobile plant. This can mean taking the reactor to the waste rather than the other way around. A mobile plant needs 3 trucks to establish the whole plant and a tanker to deliver the final fuel. This size is estimated to produce 80,000 litres per day, a suitable amount for a modest size end user, transport, mining, shipping, agriculture, or energy generation.